Get A Quote
  1. Home
  2. >News
  3. > 4 points should be paid attention to during the operation of the crusher

4 points should be paid attention to during the operation of the crusher

Feb 08 2021 The following will introduce the maintenance work of the cone crusher and effectively avoid mechanical failure Cone crusher bearings are lubricated In the crushing process of the cone crusher machine the high hardness ore will withstand greater friction and various impact forces The bearing is the main part of the load so pay attention to

Get Price
Get In Touch

You can also send a message to us by this email [email protected], we will reply tu you within 24 hours.Now tell us your need,there will be more favorable prices!

Product Introduction

How to operate the vibrating screen correctly

Jul 06 2021 4 The vibrating screen should be stopped by sequence Except for special requirements it is strictly forbidden to continue to feed to the vibrating screen after it is stopped 5 When the vibrating screen is handed over the previous operator must do a prehandover check

Jun 01 2019 During the operation you should always pay attention to prevent the large nuggets from getting stuck in the feeding port of the crusher If it happens be sure to use iron hooks to turn the ore if it needs to be taken out of the crushing chamber special equipment should be used It is strictly forbidden to carry out these tasks by hand

Dec 19 2020 4 Before each use of the metal shredder check whether the lubrication of the machine such as bearings is well lubricated and whether the lubricant in the thin oil station is sufficient The lubricity of the machine is good the output can be better the friction between the parts can be reduced and the service life of the equipment can be prolonged

Four aspects of metal shredder operation that need attention

Four aspects of metal shredder operation that need attention

Feb 20 2021 Points to note when using the wet wipe machine 20210220 By Suny Group During the operation of the wet tissue machine special attention must be paid to certain matters This is more important to everyone because many people dont understand certain things that need special attention during the operation of the wet wipe machine which will

Safety Precautions And Protective Measures For High

Jun 17 2020 5 During the operation of the crusher always pay attention to the temperature of the bearings of the crusher Under normal working conditions the temperature rise of the bearings should be within 35 degrees and should not exceed 70 degrees

During normal operation the bearing chamber butter once every 56 days4 pay attention to find out the law of operation of the machine such as machine temperature speed speed according to the situation timely processing5 the operation is stable should pay attention to check the gap coupling agreement is too tight to timely adjust

Sep 10 2019 The elbow of the thrust plate is lubricated with thick oil and needs to be lubricated every 34h 4 the temperature of lubrication There is also the temperature of the jaw crusher lubricant we must also pay attention In the use of the jaw crusher thin oil system the temperature of the oil return should not exceed 60 degrees

Matters Needing Attention In Increasing The Impact Strength Of Large Breakers Apr 20 2020 The power source of the large breaker is the pressure oil provided by the pumping station of the excavator or loader which can better clean the floating stones and the mud in the cracks of the rock during the excavation of the building foundation

Matters Needing Attention In Increasing The Impact

Matters Needing Attention In Increasing The Impact

Safety Precautions During Operation Of The Coal Handling

Aug 19 2021 Safety Precautions For Coal Fired Power Plants 1 Programmable operation should closely monitor the equipment current voltage operating status changes and alarm query monitoring operating functions in order to keep abreast of the equipment operating conditions the correct production command and fault handling

The 911MPEJAC23 is a Small Jaw Crusher of 225 X 3 manufactured to easily crush any rock from 2 50mm down to a D50 of 700 micron 28 Mesh which also correspond to a crushed discharge P80 size of 80 passing 1400 microns or 14 mesh The discharge opening closedsidesetting of this 55 mm X 75 mm bigsmall crusher you can adjusted with a wrench With a short throw at a quick 525 RPM

The oil pressure of the crusher must reach 0815kgfcm that is after the lubrication oil reaches the lubrication point the main motor can be started When the oil pressure is lower than 08kgfcm the electrical control system will give out the signal and stop feeding therefore the

Aug 08 2018 We should pay attention to the following points during the installation process of the equipment The installation site should be leveled with a solid foundation and the pit in the ground should be slightly above the ground to prevent the water flowing into the pit

Operation and Maintenance Manual HYDRAULIC BREAKER

The following instructions should ALWAYS be followed during the operation of construction equipment Protect yourself All operators and service personnel must wear appropriate safety equipment as deemed necessary by governing laws including hearing protection respirator hardhat safety shoes eye protection heavy gloves etc as required

Operation and Maintenance Manual HYDRAULIC BREAKER

Operation and Maintenance Manual HYDRAULIC BREAKER

What are the points to note when operating a metal shredder 1 Before using the metal shredder check whether there are foreign objects in the crushing chamber including the materials left in the cavity during the final processing various production tools wires iron etc If you have you should take it out in time

Pay attention to the following factors which can influence the performance of increase out the block point and remove 4 oil temperature surpass 60 Problem in rolling rubbing parts Stop the machine and check ball tile 9 frequent vibrating during 1 not enough pressure in spring 1 tighten nut in spring or change the spring

3 Replace the appropriate oil viscosity grade for the quarry crusher Generally the oil viscosity grade in summer should be appropriately higher than other times 4 During the operation of the crusher always pay attention to the temperature of the quarry crusher bearing keep it

Maintenance Jaw crusher Impact crusher cone crusher

Crushing Production Line Operation If the crushing production line is ready for operation you should pay attention to five points below 1 With the main motor turned on watch the ampere meter on the control cabinet After the peak value lasting 30 to 40 seconds the current shall drop to normal operation

Feb 08 2021 The following will introduce the maintenance work of the cone crusher and effectively avoid mechanical failure Cone crusher bearings are lubricated In the crushing process of the cone crusher machine the high hardness ore will withstand greater friction and various impact forces The bearing is the main part of the load so pay attention to

Introduction to four aspects of cone crusher maintenance

Introduction to four aspects of cone crusher maintenance

Relevant News

Online Chat Get Quotation